There is a FEB Easy solution for every need

Thanks to the wireless and battery-less buttons, FEB Easy can be used anywhere in your home, or outside of it.

Works also without Wi-Fi

Use FEB Easy on your smartphone

All the actuators can be controlled remotely through the Smart Life app and also through the Amazon Alexa and Google Assistant voice assistants.

The FEB Easy systems funcion also without Wi-Fi thanks to the kinetic switches.

Each device can be used on its own or many devices together can make a full smart system.

IP cameras with night vision

FEB Easy presents two new pan/tilt and one battery powered IP cameras

Art. 9360

Indoor pan/tilt IP camera

– Sensor: 3MP
– Tilt: 90° – Pan:355°
– IR night vision
– Motion detection with alarm through app
– Motion tracking
– ONVIF support
– Private mode for when you are in the home
– 2 way audio
– Local (on microSD – not included), or cloud (separate subscription) video recording
– Compatible with Amazon Alexa and Google Home
– Supports Tap-to-Run and automations through the app

Art. 9361

Outdoor pan/tilt IP camera

– Sensor: 3MP
– Tilt: 90° – Pan:355°
– Dual night vision: IR or full color
– Motion detection with alarm through app
– Motion tracking
– Supports automated patrolling motions
– Private mode for when you are in the home
– 2 way audio
– Local (on microSD – not inlcuded), or cloud (separate subscription) recording
– Compatible with Amazon Alexa and Google Home
– Supports Tap-to-Run and automations through the app

Art. 9362

– Sensor: 3MP
– Viewing angle: 135°
– Dual night vision: IR or full color
– Motion detection with alarm through app
– 5200 mAh battery
– 5W solar panel for charging
– Sends notifications to the smartphone when the battery is low
– Private mode for when you are in the home
– 2 way audio
– Local (on microSD – not inlcuded), or cloud (separate subscription) recording
– Compatible with Amazon Alexa and Google Home
– Supports Tap-to-Run and automations through the app

Art. 9351

Smart Wi-Fi thermostat for gas boilers

– Power supply: 95-240 Vac, 50-60 Hz
– Measurement error: ±1°C
– Temperature control range: 5-45 °C
– Operating temperature: 0-45 °C – 95% relative humidity (non condensing)
– IP rating: IP20
– Relay max current: 5A
– Temperature sensor: NTC 10k ohm, – Parameter B: 3950
– Power consumption: <1.5W
– Installation: 503 wall box, round wall box diam. 60mm
– Wireless connectivity: Wi-Fi network IEEE 802.11 b/g/n 2.4G
– Dimensions: front – 131 x 75 x 13.6 mm / back – 50.1 x 50.1 x 23.9 mm

Art. 9358

With this intelligent module you can measure the power consumption of the line it is connected to and also the voltage,
current, active power and the power factor. All these information are available via the app, together with historical
data for the power consumption. Thanks to Wi-Fi connectivity, you can also manage the On/Off status of the switch remotely or via Amazon or Google voice assistants.
This module allows you to set overcurrent protection values directly from the app, it can send you notifications if the power consumption exceeds a user set value and in the event of a power failure, it maintains the state it was in.

It cannot be controlled by the FEB Easy kinetic switches;

Dimensions: 2 DIN modules – 81 x 36 x 66;
Accuracy: ±2W within 100W, ±2% over 100W;
Maximum current: 63A

FEB Easy – Introduction

Kinetic switches 9320 & 9320/2

4-in1 pocket kinetic switch 9320/4T

IP67 Protection

Each device can be used on its own or many devices together can make a full smart system.